ds firetrap - 8 firetrap descripton supplied ready to operate the firetrap system is designed for contnuous operaton 365 days of the year. this system incorporates ip68 rated enclosures with resin dipped circuit boards for protecton against condensaton. each receiver has four independent outputs which can easily be paired with individual switches from one or many transmiters. building a bespoke control system is easy with transmiters containing up to 16 switches. features ? rugged radio remote control ? one transmiter can control many receivers ? waterproof receiver to ip68 ? transmiters available with 1, 2, 3, 4, 16 switches
firetrap system and receiver part numbers part number descripton firetrap - tx1 transmiter 1 switch firetrap - tx3 skeet transmiter 3 switch firetrap - tx4 transmiter 4 switch firetrap - tx16 transmiter 16 switch (8sw + shif key) firefly - tx - ipkit o ring, seals transmiter to ip68 transmiters ship with; wall mountng cradle, and lanyard part number descripton frequency (mhz) range** (metres) firetrap - s1prm system 1 ch prewired for promatc (duraplug) 433.92 250 firetrap - s1lap system 1 ch prewired for laporte 433.92 250 firetrap - s1as1 system 1 ch prewired for au- tosporter 433.92 250 firetrap - s1 system 1 channel 433.92 250 firetrap - rx receiver unit only 433.92 250 part number descripton frequency (mhz) range** (metres) firetrap - skeet skeet system (tx & 2 x rx s) 433.92 250 skeet systems
firetrap please read before attempting installation: this system is supplied complete with cable in order to connect to the clay trap release. warning : not all clay traps have the same wiring conventon! the system is pre - wired (as diagram below) to operate with most trap releases, before connectng, check your connections. (using a voltmeter) if you are in any doubt, do not connect the system, consult a qualifed electrician. although the system operates on 12 - 30v dc damage may occur to the receiver unit if wrong connectons are made. installaton notes an ideal installaton would be to frmly fx the firetrap - rx approx. 2 metres from the ground, in direct sight of the transmiter. lowering the height or having obstacles between transmiter and receiver will reduce range! connectng power to the receiver unit the receiver unit requires the following connectons to operate: - 12v supply (brown wire as supplied) - ov supply (yell/grn wire as supplied) when the receiver unit has power connected the power led will illuminate. this must be on for the system to operate. note: if you are pairing multple transmiter i.e. if you have purchased receivers and transmiters separately. follow the procedure detailed on page 4 to confgure your chosen system. firetrap - s1 systems are sold pre - paired. r e l a y 1 r e l a y 2 r e l a y 3 0 v 1 2 v n o n c c o m l r n l e d b u z z e r r e e d s w i t c h l r n s w i t c h p w r l e d a c k l e d j u m p e r l i n k s a n t e n n a f i r e t r a p r e c e i v e r w i r i n g t h i s d i a g r a m s h o w s t h e s t a n d a r d w i r i n g c o n f i g u r a t i o n a n d m a y b e a d a p t e d t o f i t t r a p s r e q u i r i n g o t h e r s w i t c h i n g t y p e s .
firetrap check the wiring required for your trap: the firetrap is capable of switching nearly any trap type, however wiring conventons vary between manufacturers. the relays on the firetrap can switch up to 24v dc or 230v ac @ 5a. additonal transmiters each transmiter has a unique identty. each tme a transmiter switch is operated, it transmits a secure rf signal. the receiver can to set learn this signal and pair it to any of its outputs. to pair a new transmiter switch follow this procedure: any transmiter buton can be paired to one or many of the receiver output relays. each buton must be paired to each relay individually by following this procedure: select the receiver output relay to pair: 1. briefy press the receiver pairing switch (s2) once. 2. the receiver pairing led will fash once to indicate output relay 1 is selected. 3. afer the receiver pairing led stops fashing, press the receiver pairing switch again to select the next relay. 4. repeat step 2 untl the required output relay is selected. 5. press the buton on the transmiter you want to pair to the selected relay. 6. the receiver pairing led will flash once to confrm pairing is complete. erasing receivers memory press and hold the receiver pairing switch for approx 10 seconds. release the switch and watch for the receiver led to fash to confrm erasing. press a buton on the transmiter and ensure no relay actves note: you cannot erase individual transmiters or butons confguring receiver relays the link caps (shown above) confgure the outputs operaton. the these links are connected/broken us- ing the small link cap placed over the pins. to store the setng turn power of then back on. link positons relay outputs lk1 lk2 rly 1 rly 2 rly 3 rly 4 open open 1 / 2 sec mom 1 / 2 sec mom 1 / 2 sec mom 1 / 2 sec mom closed open 1 / 2 sec mom mom mom mom open closed mom mom mom mom closed closed - - - -
firetrap technical specifcatons transmiters: firetrap - txn enclosure ratng: standard ipx8 batery type: cr2032 (supplied) dimensions: 90 x 54 x 27 mm receiver: firetrap - rx enclosure ratng: ip68 dimensions: 130 x 112 x 42 mm (not including antenna) storage temperature: - 10 to +70 o celsius. operatng temperature: - 10 to +50 o celsius. *the relay contacts in this unit are for functonal use only and must not be used for isolaton purposes electrical characterisics min typical max units supply voltage 3v v supply current ma frequency: firefly: wideband 433.10 433.920 434.70 mhz rf output power (erp) @ 433 mhz - 3 10 mw electrical characteristics min typical max dimension supply voltage for +12 v 10.5 30 vdc relay ratng* (230vac) rly1 - 4 5 12 a supply current : quiescent all relays operatng* 10 140 ma time delay from tx on switch to rx relay operaton 100 ms time delay from tx sw relax to rx relay release 300 ms is a trade name of r f solutions ltd, william alexander house, william way, burgess hill, west sussex, rh15 9ag email : sales@rfsolutions.co.uk http://www.rfsolutions.co.uk tel: +44 (0)1444 227909 fax: +44 (0)1444 227898
firetrap rf solutons ltd. recycling notce meets the following ec directves: do not discard with normal waste, please recycle. rohs directve 2002/95/ec specifes certain limits for hazardous substances. weee directve 2002/96/ec waste electrical & electronic equipment. this product must be disposed of through a licensed weee collecton point. rf solutons ltd., fulfls its weee obligatons by membership waste bateries and accumulators directve 2006/66/ec where bateries are fted, before recycling the prod- uct, the bateries must be removed and disposed of at a licensed collecton point. environment agency producer registraton number: wee/jb0104wv. disclaimer: whilst the informaton in this document is believed to be correct at the tme of issue, rf solutons ltd does not accept any lia bility whatsoever for its accuracy, adequacy or completeness. no express or implied warranty or representaton is given relatng to the informaton contained in this document. rf solutons ltd reser ves the right to make changes and improvements to the product(s) described herein without notce. buyers and other users should determine for themselves the suitability of any such informat on or products for their own partcular requirements or specifcaton(s). rf solutons ltd shall not be liable for any loss or damage caused as a result of user s own determinaton of how to deploy or use rf solutons ltd s products. use of rf solutons ltd products or components in life support and/or safety applicatons is not authorised except with express writen approval. no licences are cr eated, implicitly or otherwise, under any of rf solutons ltd s intellec- tual property rights. liability for loss or damage resultng or caused by reliance on the informaton contained herein or fro m t he use of the product (including liability resultng from negligence or where rf solutons ltd was aware of the possibility of such loss or damage arising) is excluded. this will not operate to lim it or restrict rf solutons ltd s liability for death or personal injury resultng from its negligence. mechanical dimensions 5 0 . 0 0 5 9 . 0 0 4 6 . 0 0 8 2 . 0 0 1 0 . 0 0 a l l d i m e n s i o n s i n m m
|
